MSDS Ultra Pure Actin
1 CHEMICAL IDENTIFICATION
2 COMPOSITION/ INFORMATION ON INGREDIENTS
|TRIS (2-Amino-2-(Hydroxymethyl)-1,3-Propanediol)||CAS#: 77-86-1 EINECS#: 201-064-4||<1%|
|Calcium Chloride||CAS#: 10035-04-8 EINECS#: Unlisted||<1%|
|ATP (Adenosine 5’-Triphosphate Disodium Salt Hydrate)||CAS#: 34369-07-8 EINECS#: Unlisted||<1%|
|DTT (1,4-Dimercapto-2, 3-Butanediol)||CAS#: 3483-12-3 EINECS#: 222-468-7||<1%|
|Trehalose||CAS#: 6138-23-4 EINECS#: Unlisted||<65%|
|Rabbit Protein||CAS#: None EINECS#: None||<35%|
4 FIRST-AID MEASURES
General Information: No special measures required.
Inhalation: Supply fresh air. Consult Physician.
After Skin Contact: Immediately wash skin with soap and rinse with copious amounts of water.
After Eye Contact: Rinse opened eye for at several minutes under running water. Consult Physician.
After Swallowing: Rinse mouth with water provided person is conscious. Consult Physician.
6 ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures: Wear protective clothing, respirator, chemical safety goggles, gloves.
Environmental precautions: Dilute with plenty of water. Do not allow to enter sewers/surface or ground water.
Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose of contaminated material as waste according to Section 13. Ensure adequate ventilation.
Reference to other Sections: See Section 7 for information on safe handling. See Section 8 for information on personal protection equipment. See Section 13 for disposal information.
8 EXPOSURE CONTROLS/ PERSONAL PROTECTION
Personal protective equipment
General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed. Wash hands before breaks and at the end of work. Immediately remove all soiled and contaminated clothing. Avoid contact with the eyes and skin.
Short term filter device: Filter P2.
Do not breathe. Use mechanical exhaust system.
The glove material has to be impermeable and resistant to the product/substance/ preparation. As the product is a preparation of several substances, the resistance of the glove material cannot be calculated in advance and therefore has to be checked prior to application. No recommendation can be given for the glove material for this product. Select glove materials base on penetration times, rates of diffusion and degradation of material.
Material of gloves:
The selection of suitable gloves depends not only on the material, but on quality of material and varies from manufacturer to manufacturer.
Penetration time of glove material:
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
For the permanent contact of a maximum of 15 minutes, gloves made of the following materials are suitable: Neoprene gloves.
Eye protection: Tightly sealed goggles.
Body protection: Protective work clothing.
10 STABILITY AND REACTIVITY
Chemical stability: Stable between -70°C and 37°C.
Thermal decomposition/conditions to be avoided: No decomposition if used according to specifications.
Possibility of hazardous reactions: No dangerous reactions known.
Hazardous decomposition products: No dangerous products known.
12 ECOLOGICAL INFORMATION
No data available.
14 TRANSPORT INFORMATION
DOT (Department Of Transportation) classification: This product is considered to be non-hazardous for transport.
IATA-DGR (International Air Transport Association) classification: This product is considered to be non-hazardous for transport.
16 OTHER INFORMATION
This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. The above information is believed to be correct, be all inclusive and shall be used only as a guide. PurSolutions, LLC shall not be held liable for any damage resulting from contact with the above product.